1000 Lumen Trionic LED Front Light

This manual both shows how you attach the light holder and the light on a Walker (left column below) and also how you attach them on a Veloped (right column below).

In the left-hand photo, A shows the holder attachment parts for a Walker (2 screws + 2 washers). B shows the holder attachment parts for a Veloped (1 screw + 1 knurled nut + 1 nut).

1000 Lumen Trionic LED Front Light

Attaching the Light Holder

Instructions for a Walker

On top of the black semi-vertical tube, locate the two screws that clamp the grip tube, situated in front of the brake lever.
A1. On top of the black semi-vertical tube, locate the two screws that clamp the grip tube, situated in front of the brake lever.
Loosen both screws with the 5mm allen key included with the LED light.
A2. Loosen both screws with the 5mm allen key included with the LED light.
Remove the two screws from the grip clamp.
A3. Remove the two screws from the grip clamp.
Place the light holder on top of the grip clamp, with its circular and slotted light attachment pointing forwards and upwards. Enter the two screws with washers into the holes of the clamp.
A4. Place the light holder on top of the grip clamp, with its circular and slotted light attachment pointing forwards and upwards. Enter the two screws with washers into the holes of the clamp.
Tighten the two screws with the 5mm allen key. NOTE: It is important that you tighten the screws properly as they secure the grip tube with its rubber grip and brake lever.
A5. Tighten the two screws with the 5mm allen key. NOTE: It is important that you tighten the screws properly as they secure the grip tube with its rubber grip and brake lever.

Instructions for a Trionic Veloped

Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
A1. Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
Replace the old screw with the longer screw included with the LED light. Attach the longer screw to the hinge and tighten it with the 4mm allen key.
B2. Replace the old screw with the longer screw included with the LED light. Attach the longer screw to the hinge and tighten it with the 4mm allen key.
Attach the short angled end of the light holder to the lower end of the screw, on the downside of the grip bar. Fasten the holder with one washer and the knurled nut.
B3. Attach the short angled end of the light holder to the lower end of the screw, on the downside of the grip bar. Fasten the holder with one washer and the knurled nut.
For a more secure holder attachment, avoiding the holder to unintentionally turn sideways, replace the knurled nut with the included stainless steel nut and tighten it with a 10mm spanner.
B4. For a more secure holder attachment, avoiding the holder to unintentionally turn sideways, replace the knurled nut with the included stainless steel nut and tighten it with a 10mm spanner.
This photo shows the light holder as correctly attached.
B5. This photo shows the light holder as correctly attached.

Attaching the LED Light to the Holder

Instructions for a Walker

Identify the circular front end of the light holder, with two slots for attaching the light.
A6. Identify the circular front end of the light holder, with two slots for attaching the light.
Push the slotted bracket of the light into the slots of the holder and make sure they are aligned. Seen in the traveling direction of the Walker, enter the included wingnut from the left and tighten it.
A7. Push the slotted bracket of the light into the slots of the holder and make sure they are aligned. Seen in the traveling direction of the Walker, enter the included wingnut from the left and tighten it.

Instructions for a Trionic Veloped

Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
B6. Locate the screw at the center folding hinge of the U-shaped grip bar of the Veloped. Unscrew the screw with the included 4mm allen key and remove it.
Identify the circular front end of the light holder, with two slots for attaching the light.
B7. Identify the circular front end of the light holder, with two slots for attaching the light.

Instructions for Use

Overview

Overview

Caution

It is normal for the battery to reach a high temperature (up to 104°F / 40°C) during charging due to chemical reactions within the battery. The battery may also become warm if it is not fully drained before charging. Several factors can affect the battery's lifespan, including the type of cell, usage strain, maintenance routine, temperature, and the number of charge cycles. Generally, a higher battery capacity results in a longer operation time. The battery capacity may decrease to approximately 80% of its original capacity after 300–500 charge/discharge cycles. With proper care, the battery can have a lifespan of up to 3 years. Water resistance is for rain water only. Do not submerge the battery or the whole light in water when cleaning. Clean the light with a soft damp cloth when needed.

Battery Performance

Battery performance is significantly affected by temperature variations:

•Low Temperature: At 0°C, capacity decreases by 5–10%, reducing operation time by 50%. At -20°C, capacity drops by 30%, potentially shortening operation time by 70%. Performance returns to normal when the temperature rises to 20°C.

•Self-Discharge Rate: At room temperature, the battery loses about 1% of its capacity per day. When stored at 40°C, the self-discharge rate increases, leading to a loss of approximately 5% of capacity per day.

To maintain optimal battery performance, avoid exposing it to extreme temperatures and store it in a cool, dry place.

If you do not use the battery for a long time be sure to recharge the battery every 3 months.

Safe Mode

When the battery is low, the light will automatically switch to a 50-lumen high-beam safe mode, providing an additional 30 minutes of operation.

How to operate the light

Press and hold the switch for 2 seconds to turn the light on or off. Click once to cycle through modes, and double-click to enable ultra-bright mode (1000 lm).

Press and hold the switch for 2 seconds to turn the light on or off. Click once to cycle through modes, and double-click to enable ultra-bright mode (1000 lm).

The package contains

Press and hold the switch for 2 seconds to turn the light on or off. Click once to cycle through modes, and double-click to enable ultra-bright mode (1000 lm).

Charging And Powerbank

Press and hold the switch for 2 seconds to turn the light on or off. Click once to cycle through modes, and double-click to enable ultra-bright mode (1000 lm).

Product Reviews    

  • 14 17

    Happy Customer…

    A little bulky at times but I am a happy customer.…

    Trionic
  • 9 8

    From the neighbor to your own Veloped…

    Saw it at my neighbor's house and bought it because I was impressed by every aspect. It looks great, handles well (the brakes and function)—which is difficult to grasp for someone with dementia (in our case), but otherwise the brakes work perfectly. …

    Read the Full Review 
  • 12 0

    Brilliant walking aid. Trionic Sport…

    Brilliant walking aid. Worth every penny. I get stopped every time I go out. Questions and even photos are taken. I’d be lost without it. I suffered a brain haemorrhage and am continually dizzy. It’s robust and like nothing I’ve used. Without it, I’d…

    Read the Full Review 
    Trionic
  • 11 0

    Trionic Veloped Trek…

    There is really only one thing to say about my Veloped Trek and that is FABULOUS. The design and engineering are just superb - you have thought of everything. My Trek has absolutely changed my life and although I have not had it very long, I am now a…

    Read the Full Review 
    Trionic
  • 23 12

    My Trionic Trekker 12 came yesterday……

    My Trionic Trekker 12 came yesterday and within 5 minutes had it’s wheels on, a bottle of water in the basket and we were on our first walk off pavement in over 10 years ...wonderful! There were flowers, painted stones someone had left for others to …

    Read the Full Review 
    Trustpilot
  • 7 8

    Able to walk outdoors again…

    The Trionic Veloped Sport was an excellent purchase. Because of cerebellar ataxia, I am no longer able to walk without a rollator. This device allows me to walk outdoors again, which is huge! It is worth every cent.…

    Trustpilot
  • 8 8

    Great experience all the way around!…

    I've taken my trek miles on the desert and it'll go anywhere. The training is bringing me to the point where I can walk without it. Even when I had flats from goathead thorns--the bane of all OTR cyclists--they were easily fixed at a bike store. Trio…

    Read the Full Review 
    Trustpilot
  • 15 8

    Independent walking again…

    I have had my Veloped Tour for just over a month and am absolutely delighted with it. Apart from back issues which had limited my walking, this year I have a balance problem. The Trionic has enabled me to get back to enjoying the countryside both on …

    Read the Full Review 
    Trionic
  • 7 0

    Navigate rough terrain…

    The product arrived within days of ordering, which amazed us since it came from Sweden. We are very happy with the product and would recommend it to others needing a mobility device that can navigate rough terrain.…

    Trionic

Subscribe to our newsletter!